Have you ever wondered how a band vocalist reaches

Condenser microphone is a kind of microphone, which stays connected with the throat of the speaker. It has got a strap that ties down the microphone with the neck of the person speaking. This microphone reacts directly to the vibration of the neck. It gives a clear sound and it can capture your voice even it is kept far from your mouth. The best thing about this condenser microphone is, it can pick up sound in loud environments such as night clubs, discs etc. it has got a specific design that helps this microphone to copy these kind of sounds. It is different from the other conventional microphones. In a nightclub, the conventional microphones will not be able to copy one voice distinctly. The voice will not be prominent because of the ambience sound. It can even copy the whispers. The aircrafts of the World War 2 era used this microphone. There are different kinds of condenser microphones used for different purposes. Below we are providing you the list of some such microphones. Mission sniper pro condenser microphone: The army mainly uses this kind of microphone. This microphone is specially made for environments, which are tough and operational. The law enforcement, HAZMAT, military use them. For such operation purpose, this mike offers a lot of facilities. It gives you a clear sound even in a crowded place. You can get the sound without any ambience noise. Even the whisper sounds clear in this mike. It can be used with helmets and gas masks. PC condenser microphone: This microphone is specially made for online gamers. It gives you a clear sound. While playing this microphone helps you to play the game properly. It has got an acoustic ear coil attached with it. It gives you comfort. It also looks pretty trendy. Cell phone condenser microphone: I think you have already understood what this mike does from its name. It is made for the cell phones. It gives you a hands free comfort. You need not hold the phone anymore. Just plug it in with your phone and you are on to a conversation and that too without using your hands. It gives you a clear sound and cuts down all the background noise. So, from now on you will not have to hear the yelling of her mother while talking to your girlfriend. It will cut down all the noise. However, before you start repairing your condenser microphone here are a few general tips to help you to stop it from failing again. The microphone being a responsive object is sensitive to even slight changes in the weather. It is always advisable to keep them inside a box wrapped in moisture absorbents. If the humidity or the moisture content in the air affects the membrane of the microphone, the sound quality may start distorting or sometimes even disturbing the entire signal flow. Various condenser microphone are found faulty due to various reasons. You can find a microphone with no transmission or low or erratic RF output. In certain microphones the ON and OFF switch is sometimes faulty. When the ON and OFF switch is faulty, you can be assured that at least the audio output is not affected. However, a faulty R.F. output or driver transistor can produce some symptoms that may partially or fully disturb the sound content and quality. You can use a bridge rectifier to protect rig against reverse polarity. Applying a light oil or WD40 to the contacts can in most of the cases, cure noisy crackling that is caused by a condenser microphone switch. It can also be used in crackling squelch or volume controls and to clean the outside of rigs and to improve the clarity of channel displays. In order to avoid confusion you can follow this small advice that will help you to cope with all your extension problems even in the future. Instead of having several power leads with different plugs trailing across the repair bench, cut all your power leads down to 6 inches and fit them to a connector block with just one pair of wires going back to the power supply. Thus, this will make your work much more easier. Whatever you do be sure that most of the power transistors and regulators usually contain poisonous substances, in order to be safe and sure, wash hands and nails scrupulously after handling broken or cracked devices and various parts of the microphone. A danger also exists on some home based rigs and power supplies. They have only two core cable or switches in the neutral wire. So be aware. The earth tags should be bolted to chassis and not pop riveted to a transformer plug. Another important thing that you should remember is about microphone socket pins. The microphone socket pins splits can often close up and can further cause a bad connection. In a microphone when the knob is loose, do not wrap knob along the diaphragm with a tape to solve the problem. Use a screwdriver to tighten the knob. Hence, getting your condenser microphone repaired is no rocket science. Anyone can do it provided he or she is well adapted to the mechanism of a microphone and can identify the areas of problem.